BEGINNER'S GUIDE TO INSTALLING A NEW SHOWER UNIT

Beginner's Guide to Installing a New Shower Unit

Beginner's Guide to Installing a New Shower Unit

Blog Article

Schedule Here

We have stumbled upon this post involving How to Build a Shower Enclosure for Your DIY Bathroom down the page on the net and believe it made good sense to share it with you over here.


How to Install a One-Piece Shower Unit
A successful shower installation calls for cautious planning and a lot of job. For the most part, you will need to do 3 sorts of jobs: framing walls, setting up the plumbing, and also ending up walls.

Prep work


Firstly, you have to decide on the sort of shower that you desire to mount. It is important to establish whether the picked shower can dealing with particular systems and can control a secure level of water through the boiler. A lot of shower units nowadays are developed to be flexible to various water pressures (such as kept warm water as well as cool mains).
It is additionally crucial to take into consideration the water stress as well as the preparation of the piping as well as drain for the shower

Different Kinds Of Shower Units


  • Push-on Mixer: The tube and spray parts of the push-on mixer shower unit can be linked to the bath faucet based on your requirement, as well as the water temperature can be adjusted using the taps. Push-on mixers are cheap as well as incredibly easy to set up. However, although the pipe connection is straightforward, it is quickly dislodged. Additionally, it is bothersome to adjust the temperature.

  • Bath/Shower Mixer: The pipe and also spray of this type of shower are integrated with a bathroom mixer tap, and the temperature can be readjusted with the bathroom taps. It is a really affordable alternative as well as no added plumbing is entailed. Nonetheless, the bath/shower mixers likewise experience bothersome temperature level control alternatives.

  • Manual Mixer: The tube and spray of a manual mixer shower unit belong of the wall unit as well as the hot and cold water materials are connected to a single shutoff The temperature and pressure of the water are managed with either one or a range of handles (in a lot more pricey showers). Although temperature level control is much easier in manual mixer kinds, they are a lot more costly than the formerly discussed mixers. They additionally need additional plumbing of cold and hot water system pipes.

  • Thermostatic Mixer: The hose pipe as well as spray of this shower type are a part of the wall surface unit and also the cold and hot water products are linked to a single valve here too. It is total with an integrated stabiliser to self-adjust the water temperature as well as to prevent it from ending up being as well hot. Among the greatest benefits of a thermostatic mixer shower kind includes hassle-free temperature level control. However, it is one of the most expensive of the different mixer alternatives.

  • Power Shower: A power shower is a single unit having a powerful electrical pump that can altering both the water stress and also temperature level. This kind of shower can be fitted if there is water system from a cold water cistern as well as a warm water cyndrical tube. A power shower makes the change of both pressure as well as temperature very easy. On the other hand, it disagrees for water warmed directly by the shower or where the water is supplied by a combination boiler under mains pressure.

  • Electric Shower: An electrical shower is plumbed into a keys cold water supply and also it heats up the water electrically. It is very important to keep in mind that for this shower type to be installed, the keys stress requires to be at least 0.7 kg/sq centimeters (10lb/sq in). The device enables the temperature level and also pressure to be adjusted using a knob. Versions with temperature stabilisers are better as they continue to be unaffected by various other taps elsewhere in operation within the house. A major disadvantage of electrical showers is that the control handle just allows for the alternative of high temperatures at less pressure, or lower temperatures at a higher pressure. This is troublesome in the winter when the spray is usually weak as well as the keys water is chillier. Nonetheless, this problem is dealt with in some models which are available with a winter/summer setup.

    • Approach


    Relying on the kind of shower you wish to install, the shower head need to either be suited order to avoid its contact with the water in the bathroom listed below or the base tray, or it should have a check shutoff.
    Before starting, it is a good idea to mark the settings of the shower head and also control, and also to plan the pipe-work entailed. Furthermore, the drainage system to remove the drainage will require to be prepared. Both positions of the cord course and the shower switch will certainly additionally need to be thought about if an immediate or electrical shower unit is being set up.
    Make use of the direction overview supplied with the shower system to fit the shower control.Before suitable the pipes that will provide the water to the shower system, it is essential to remove the water system. In order to safeguard the pipes, they ought to be given a water resistant covering and additionally fitted with separating shutoffs. The pipes can then be buried into the wall and glued over to neaten the general look.
    Fit the base tray, shower head, as well as fittings.
    Link the major shower control to the pipes that will certainly be supplying the water (This might call for a women screw thread adapter).
    Reconnect the water supply as well as test the pipes for any type of leaks, as some may need tightening up.
    If you are setting up an electric shower, keep in mind to switch off the electrical energy supply prior to making any type of electric links. As soon as these links have been made (there ought to be support within the user's manual), the power supply can be changed back on.

    Changing Water Pressure to Fit Your Shower


    The cold water storage tank can be raised to a higher elevation (in some cases just 150mm (6inches)) by installation a strong wood assistance under it - perhaps made up of struts as well as blockboards. If you choose this option, the main and also distribution pipelines will certainly also have to be increased to satisfy the new elevation of the reservoir.
    Alternatively, a booster pump (a solitary pump or a dual/twin pump) can be fitted. Whichever type is selected, it needs to be attached right into the power supply in order to operate.

    Piping and Drain


    It is best to utilize 15mm size supply pipes, and also make the runs to the shower as brief and also straight as possible so as to keep maximum pressure and reduce warm loss. In addition, by minimising making use of elbow joints for pipe edges, you can lower the resistance in the flow of the water supply. You can accomplish this by flexing the pipes instead.

    Most Usual Errors


  • Violating or disregarding local code restrictions.

  • Making use of pipes that are as well little.

  • Affixing copper to galvanized without using a brass or dielectric fitting in between both.

  • Not making use of tape or pipeline compound at threaded joints.

  • Not leveling your fixtures when mounting them.

  • Not setting up an air void filling up for components.

  • Cutting supply stub outs also short to set up the shutoff valves onto after the ended up wall surface is in location.

  • Not effectively straightening tubing right into fittings or quit valves. (Forcing the nut onto the compression ring at an angle when the tubing goes to an angle will certainly cause a leak.).

  • When turning the water back on in your house, constantly run the outside hose pipe valve or flush your commodes to bleed dirt and air from the lines. This particles can cause issues in your sink faucets and other plumbing trim.



    • How Do You Install a Shower? Follow This Guide


    Installing a Shower at a Glance


  • Tools & Materials: Level, electric drill, caulk, hole saw, cedar shims, shower unit

  • Step 1: Drill pilot holes

  • Step 2: Prep fixture holes

  • Step 3: Move unit into place

  • Step 4: Caulk corners and base

  • Step 5: Attach door

  • Step 6: Install shower pan

    • Whenever plumbing is involved in a DIY project, people worry about what might go wrong. The truth is that installing a shower isn’t that complicated, and you can save a lot of money by doing it yourself. You shouldn’t need to make any alterations to your plumbing to complete the job, and most of the tools you need will be provided in your new shower kit.


    Can I Install a Shower Myself?


    Even if you’ve never installed a shower before, you’ll find this to be a project that is perfectly suited for DIYers with a moderate level of experience. Whether you're doing a bathtub conversion or installing a new stall, most of what you need comes in shower kits that you can purchase from a hardware store. The first thing you need to do is determine what type of shower stall you want.


    Single-panel stalls are the easiest to install because they come preassembled. All you need to do is put them in place. Multi-panel showers require a few additional steps, but you’ve got more control over the appearance of your unit. Multi-panel units are also much easier to handle if you’re going to do the installation without any help.


    Be sure to take all appropriate safety precautions, such as wearing eye protection and gloves. When you’re removing or installing a shower unit, you might kick up debris that could hurt your eyes. You’ll also need to work with equipment that will get extremely hot, so be sure to have safety gloves handy.


    Tools and Materials


  • 2- to 4-foot level

  • Electric drill with a 1/8-inch drill bit

  • Caulk

  • 2-inch hole saw

  • Cedar shims

  • The unit itself

    • Before You Begin: Prep the Space


    It’s highly important to measure your space accurately before putting the stall in. Measuring from the floor upward and from each corner outward will ensure you’ve got the right measurements. What you’re looking for is where the plumbing apparatuses are going to come through the stall. Transfer these measurements over to the back of your unit by drawing the locations of these holes using a pencil or marker.


    Pull out your old shower and make sure to scrape off all the old caulking. Be thorough because you want to work with smooth surfaces for the best installation. Once you’ve pulled out your existing shower, you need to make sure that the floor is clean and dry. The best way to clean debris is with a shop vacuum, as it’ll soak up water and dirt together.


    If you’re experiencing any plumbing issues, such as low water pressure, this is a perfect opportunity to solve them. Make sure that the pipes themselves are not in need of patching and clean your showerhead. When you turn the water back on after your project, check the pipes for signs of wear or disrepair. Anything beyond minor repairs should be handled by a plumber, and this is the best time to bring in a professional.


    If the floor has any moisture at all, don’t proceed until it’s completely dry. The last thing you need is for the floor to rot or invite mold and mildew into your base. Once everything is dry, apply waterproof wallboard to the walls. This can be attached with screws or nails, then sealed with caulk so that water doesn’t seep into any crevices.

    https://www.homeserve.com/en-us/blog/how-to/install-shower/


    How to Install a Shower Enclosure

    We hope you enjoyed our post about How to Install a Direct-to-Stud Shower Enclosure. Thank you for taking time to browse our blog post. Sharing is nice. Helping people is fun. Thanks for going through it.


    Request Estimate

    Report this page